The SS5 CrossLink Roof Kit for the 2019-2024 Honda Talon is the ultimate lighting upgrade for off-road enthusiasts. Designed to provide both rugged durability and exceptional light output, this kit features our innovative SS5 LED pods. With eight selectable backlight colors and a modular CrossLink design, it combines aggressive styling with unmatched performance. Whether you're navigating trails or lighting up your campsite, this kit ensures you have all the light you need.
Built with durable stainless steel brackets and engineered for tough conditions, the SS5 CrossLink Roof Kit is plug-and-play for easy installation. This guide walks you through every step to get your light bar installed and ready to perform. Watch our installation video or continue reading below for detailed instructions!
Table of Contents
Installation Video
Tools Required
- 5mm Allen Wrench
- 10mm Socket and Wrench
- 13mm and 14mm Wrenches
- Phillips Head Screwdriver
- Trim Removal Tool or Flathead Screwdriver
- Zip Ties
Installation Instructions
Step 1 - Remove Front Roof Bolt
Using a 5mm Allen wrench, remove the front Allen bolt from the roof. Save the washer for later use.
Step 2 - Install Roof Bracket
Place the washer back on the roof, followed by the CrossLink windshield bracket. Secure it with the included 5mm Allen bolt, but do not tighten it fully yet.
Step 3 - Secure Lower Bracket
Align the lower bracket with the roll cage and secure it using the included nut and bolt. If you have an aftermarket windshield covering this area, remove or adjust it. Tighten the assembly using a 10mm socket and wrench, then fully secure the top Allen bolt. Repeat this step for the other side.
Step 4 - Assemble Light Bar
Align the SS5 CrossLink Light Bar with the first notch of the hardware. For detailed assembly instructions, check out this video. Secure both support link mounts to the underside of the hardware using a 10mm socket.
Step 5 - Mount the Light Bar
With assistance, lift the light bar into place and align the top two mounting points with the through holes of the bracket. Secure it using the included 10mm bolts on both sides.
Step 6 - Adjust Support Mounts
Press the support link mounts against the roof and tighten them using a 13mm and 14mm wrench. Repeat this process for the other side.
Step 7 - Wire the Harness
Begin connecting the eight-pod harness to each pod, ensuring the male end of the harness is on the driver’s side. Secure any loose wiring with zip ties.
Step 8 - Connect to Power
Remove the battery cover by releasing three metal clips. Loosen the battery terminals with a Phillips head screwdriver, and connect the positive and negative leads from the harness. Secure the fuse and relay before replacing the battery cover.
Step 9 - Install the Switch
Use a flathead screwdriver to remove the three clips holding the trim. Route the switch and DT connector through, then replace the clips. Position the switch along the driver-side roll bar near the seat, securing it with zip ties.
Step 10 - Finalize Installation
Test the system for functionality. If everything works, secure all loose wiring with zip ties and reassemble any parts removed during installation.
The installation is now complete. Enjoy your new SS5 CrossLink Roof Kit!
Questions About the Installation?
If you have any questions about installing the SS5 CrossLink Roof Kit for the 2019-2024 Honda Talon, contact us via our support page.
Where Can I Buy the SS5 CrossLink Roof Kit for the 2019-2024 Honda Talon?
If you're ready to upgrade your 2019-2024 Honda Talon with the SS5 CrossLink Roof Kit, visit DiodeDynamics.com or use our Dealer Locator to find a dealer near you.
Looking for more lighting options for your Talon? Check out our full selection of Honda Talon Lighting Upgrades.
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
This Installation Guide is for the following SKUs: DD7917, DD7918, DD7919, DD7920, DD7916P.
Share This Post