Thank you for your purchase of this unique product for your new Ford Mustang! With Diode Dynamics Pro Series Multicolor DRL LED boards for the 2018-2023 Ford Mustang, you will be able to convert your factory LED Mustang DRL “bars” inside the headlight into full multicolor functionality, along with a sequential amber turn signal feature.
Please note: Headlights must be opened before proceeding with the installation. Professional installation is strongly recommended. Please contact us if you need assistance locating an installer, or use our dealer locator tool to find an installer near you.
Check out our installation video, or continue reading for step-by-step instructions below!
Table of Contents
Installation Tools
- Cutting Pliers
- 5-Minute Epoxy
- Phillips Screwdriver
Installation Video
Mounting Instructions
Step 1 - Open Headlight Housing.
Open the headlight housing by removing the four screws holding the back of the headlight housing to the lens. Set the lens aside on a soft surface to avoid scratching or marring the surface.
Step 2 - Remove Bezel.
Remove the three Phillips screws holding the white DRL bezel in place. Once the screws have been removed, pull the bezel away from the headlight housing.
NOTE: If you are installing these boards on an EU/AU spec Mustang, skip to Step 5.
Step 3 - Remove Board Connector.
Unplug the factory board connector and tuck it away. It won’t be reused.
Step 4 - Remove LED Boards.
Bring the DRL bezel to a clean area. Using cutting pliers, remove the three plastic rivets holding each LED board to the bezel and remove the LED boards.
NOTE: Be sure not to remove the two mounting tabs. They will be needed to align your new LED boards.
Step 5 - Install New LED Boards.
Place your new Diode Dynamics LED boards into position. All holes should align perfectly. Secure the new boards in place by applying epoxy or another permanent adhesive where the plastic rivets were removed. The epoxy should create a bond between the plastic rivet mounting point and the board.
Use enough epoxy so that there is a bond all the way around the rivet, contacting the board fully. We recommend securing the board labeled "3" first and working your way forward.
Step 6 - Reinstall Bezel.
Once the epoxy is fully set, reinstall the white bezel to the main headlight housing using the original screws.
Step 7 - Route Wiring.
Run the wiring out of the headlight, sealing any holes that you may create.
Wiring Instructions
Step 8 - Connect to Driver.
Connect the LED board to the driver. Then using the JST-to-M8 adapter wire included with the Diode Dynamics RGBW controller (sold separately), connect the driver to the controller. See the diagram below.
IMPORTANT: DO NOT plug the LED panel directly into the controller without the driver. The LEDs must be plugged into the driver first to control the power.
Step 9 - Connect Power.
Connect your RGBW controller to 12V power and ground. This will dictate when the panels turn on. The most popular wiring choice is listed in the table below.
Step 10 - Complete Installation.
Mount drivers and controller, and tuck all wires. Drivers should be mounted outside of the headlight for serviceability, in a location away from the engine block to avoid excessive heat buildup. Test thoroughly, reseal the headlight, and reinstall onto the vehicle.
Questions About the Installation?
If you have any questions or issues installing RGBW™/RGBWA™ DRL LED Boards in your 2018-2023 Ford Mustang, please contact us for further information.
Where Can I Buy 2018-2023 Ford Mustang RGBW™/RGBWA™ DRL LED Boards?
If you’re ready to upgrade your 2018-2023 Ford Mustang with RGBW™/RGBWA™ DRL LED Boards, you can purchase one by clicking here or using our dealer locator to find a dealer near you.
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
This Installation Guide is for the following SKUs: DD2243, DD2245, DD2254.
Share This Post