The HitchMount LED Pod Reverse Kit for the 2015-2020 Ford F-150 allows you to install one SSC1 or C1R LED Pod in your 2-inch trailer hitch receiver, adding a high-power reverse light, additional running light, and an optional 4th brake light with the C1R option.
The following installation guide will provide you with detailed instructions on how to install the C1R HitchMount LED Pod Reverse Kit on the 2015-2020 Ford F-150. Check out our installation video, or continue reading for step-by-step instructions below!
Table of Contents
Installation Video
Mounting Instructions
Note: If you would prefer to disable the Safety Strob feature of the C1R HitchMount LED Pod Reverse Kit, simply cut the purple wire that is looped on the 7-pin harness.
Step 1 - Disconnect Factory Brake Signal Harness.
From under the vehicle, look up at the frame next to the spare tire on the driver's side to locate the connector for the factory brake signal harness. Then disconnect it.
Step 2 - Connect New Brake Signal Harness.
Plug the new Brake Signal Harness in line with the factory harness that was disconnected in Step 1.
Step 3 - Disconnect Factory 7-Pin Connector.
From underneath the bumper, disconnect the factory 7-pin trailer connector by depressing any locking tabs and pulling straight out.
Step 4 - Plug-In Amp Connector.
Remove the dust cap from the brake signal harness amp connector and plug it into the new 7-pin Connector Harness.
Step 5 - Plug 7-Pin Connectors In Line.
Plug the connectors on the new 7-pin harness in line between the factory harness and the 7-pin connector on the back of the bumper that was disconnected in Step 3.
Step 6 - Route the DT Connector.
Route the DT connector through the back of the trailer hitch receiver. Then zip tie any loose wiring clear of any hot or moving parts.
Step 7 - Connect HitchMount Pod to Harness.
Remove the dust cap from the DT connector and plug the DT connector into your LED pod.
Step 8 - Install HitchMount LED Pod.
Using the patent-pending HitchMount clip, simply push the LED Pod into the trailer hitch receiver until it snaps into place.
Step 9 - Test Function.
Test the functionality of the HitchMount LED Pod Reverse Kit and then secure the wiring harness with the included zip ties to complete the installation.
Step 10 - Removing HitchMount.
To remove the HitchMount, depress the clips on either side and apply forward pressure to slide the lamp out of the receiver. Unplug the wire harness. If you plan to leave the harness disconnected for an extended period, unplug the harness from the 7-pin and 12-pin connectors as well for safe storage.
Otherwise, simply reinstall the dust cap and tuck the DT connector out of the way until it is again needed.
OPTIONAL: Using HitchMount with a Hitch Pin
The HitchMount has been designed to stay securely in place during use. If you would like to add a locking hitch pin for added security (not included), you may easily accomplish this with slight modification. This modification does not void any manufacturer warranty.
Step 1 - Cut Out Retention Tabs.
To do so, push the retention tab outward and use a cutting tool to cut out the circular section on the tab. Repeat on the other side.
Step 2 - Connect HitchMount Pod to Harness.
Plug the DT Connector into the pod, and slide the HitchMount into the trailer hitch receiver.
Step 3 - Insert The Hitch Pin.
Slide the hitch pin into place with one hand, as you align the HitchMount with your other hand. It should be a tight fit, which will prevent rattling and movement once installed. Lock the pin if desired.
Questions About the Installation?
If you have any questions or issues installing the HitchMount LED Pod for the 2015-2020 Ford F-150, please contact us for further information.
Where Can I Buy The 2015-2020 Ford F-150 C1R HitchMount LED Pod Reverse Kit?
If you're ready to upgrade your 2015-2020 Ford F-150 with the C1R HitchMount LED Pod Reverse Kit, you can purchase one by clicking here or using our dealer locator to find a dealer near you.
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
Note: This guide is only for the C1R Kit.
This Installation Guide is for the following SKUs: DD7648
Share This Post