The Stage Series Reverse Light Kit for the 2022-2024 Ford Maverick adds LED Pods as high-power reverse lights and eye-catching red accent lights. The following installation guide will provide you with detailed instructions on how to install the Stage Series LED Reverse Light Kit for the 2022+ Ford Maverick. Continue reading for step-by-step instructions below!
Table of Contents
Installation Video
Installation Tools
- Ratchet
- 7mm Socket
- Phillips Screwdriver
- 4mm Allen Wrench
- 3/8" Wrench
- 13mm Wrench
Mounting Instructions
Step 1 - Assembling SCC1 Reverse Light Brackets
To begin our installation, we'll place our C1 U-brackets over the long slot on our reverse light bracket and secure it by dropping our included carriage bolt through. Then you can slide our washer and lock washer followed by threading on our nut only hand tight to leave room for adjustment later. 
Step 2 - Removing Factory Bumper Bolts
Heading under the vehicle, we can use a 7mm socket to remove the two innermost factory bolts on the back of the bumper trim. For reference, we're beginning on the driver's side of the vehicle.
Step 3 - Installing SSC1 Reverse Light Brackets
With the factory bolt removed, we can slide our assembled C1 reverse light bracket in place and resecure it using the 7mm bolt that we just removed.
Step 4 - Installing SSC1 LED Pod
Now we can slide our SSC1 Sport LED pod in between our u-bracket and loosely secure the pod in place using the included hardware. This hardware will be fastened with a 5/32" allen key and 3/8" wrench. 
Step 5 - Positioning SSC1 LED Pod
At this point, you can slide the LED pod forward or back to the position of your choice. Once you've determined where you like, you can secure the bolt using a 13mm wrench. 
Repeat these steps on the other side of the vehicle.
Wiring Instructions
Step 6 - Removing the Driving Side Tail Lamp
At the back of the truck, drop the tailgate and locate the drive-side tail lamp. There will be (2) 8mm screws holding it in place that we'll be removing using a ratchet and 8mm socket.
Step 7 - Disconnecting the Factory Tail Lamp
Once the two bolts are removed, firmly tug to remove the tail lamp from the body of the vehicle, and then disconnect the factory harness by pressing on the release tab.
Step 8 - Plugging in Reverse Light Wiring Harness
Taking the included harness in our kit, feed the DT connectors down through the tail light pocket until the in-line adaptor is left and plug it in-line.
Step 9 - Re-Installing the Factory Tail Lamp
You can now snap the tail lamp back in place and secure it using the (2) factory 8mm screws.
Step 10 - Routing the DT Connectors
Underneath the vehicle, you'll notice our harness with our DT connectors. The harness and DT connectors will need to be routed over the driver's side bed support to keep away from the exhaust.
Note: If you decide to plug our harness into the passenger-side tail lamp, you'll need to pull back the splash guard under the Maverick to gain access to the DT connectors apart from our harness.
Step 11 - Plugging in DT Connectors
Now you can take the short end of our DT harness lead and plug it into the back of the driver-side C1 LED pod.
Then you can take the DT connector with the additional lead up and over to the passenger side C1 LED pod and plug it in.
Step 12 - Test for Function
With both C1 pods connected, test to ensure the function of the red running lights along with the white reverse light feature. With everything operating properly, be sure to go back and zip-tie up any loose wiring and ensure all hardware is secure. 
The installation is now complete. Enjoy your Stage Series Reverse Light Kit for the 2022-2024 Ford Maverick!
Questions About the Installation?
If you have any questions or issues installing the Stage Series Reverse Light Kit for the 2022-2024 Ford Maverick, please contact us for further assistance.
Where Can I Buy a Stage Series Reverse Light Kit for the 2022-2024 Ford Maverick?
If you’re ready to upgrade your 2022-2024 Ford Maverick with a Stage Series Reverse Light Kit, you can purchase one by clicking here or using our dealer locator to find a dealer near you.
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
This Installation Guide is for the following SKUs: DD7564P, DD7754, DD7755
Share This Post