Looking to improve visibility on your Honda Talon? Our SS3 LED Headlight Kit is the ultimate upgrade for off-road adventures. This direct-fit kit replaces your factory headlights with Diode Dynamics SS3 LED pods, providing dramatically increased light output with a custom, aggressive look. Watch our installation video or follow the step-by-step guide below to get started!
Table of Contents
Installation Video
Tools Required
- Flathead screwdriver
- Trim removal tool
- 10mm socket & wrench
- 5mm Allen wrench
- Phillips head screwdriver
- 13mm wrench
- Zip ties (for wire management)
Installation Instructions
Step 1 - Remove the Hood and Front Components
Twist the hood latches and firmly pull up on the corners to remove the hood. Then, disconnect the headlight harness by pressing the locking clip and pulling the connector away.
Step 2 - Remove the Bumper and Factory Headlights
Remove four plastic clips, four 10mm bolts, and five 5mm Allen bolts from the front cowl and set it aside. Use a 10mm socket to remove four 10mm bolts securing the headlights.
Detach the outer plastic clip and the 5mm bolt from the headlight shroud. Then, remove two additional plastic clips—one behind the headlight bucket and one in the inside corner of the headlight shroud.
Use a 10mm wrench to remove the 10mm bolt from the side of the bumper. Remove two plastic clips from the skid plate using a flathead screwdriver or trim tool. Lift up on the fenders and pull the bumper forward to remove it.
Step 3 - Remove the Factory Headlight Assembly
Remove the headlight cap and unplug the factory bulb. Use a Phillips screwdriver to remove the screw and spring from each headlight—these will not be reused.
Pull the headlight plastic and headlight bucket apart to release the headlight pin, then fully remove the factory headlights.
Step 4 - Assemble the SS3 LED Headlights
Attach the included bracket to each SS3 LED Pod using the supplied hardware. Secure the pod to the bracket by inserting the carriage bolt, then tightening the washers, lock washers, and nuts with a 13mm wrench. Repeat these steps for the other pod.
Make sure the Combo Beam (low beam) pod is positioned on the outside, and the Driving Beam (high beam) pod is positioned on the inside.
Step 5 - Install the SS3 Headlights
Plug the provided wiring harness into each SS3 pod, ensuring the low beam is connected to the Combo Beam and the high beam is connected to the Driving Beam.
Route the backlight wire out of the dust cap opening and position the SS3 headlight assembly inside the factory housing. Lift up on the fender and carefully insert the pods and bracket into place.
Loosely install the provided Allen screws and nuts into the middle, inner, and outer mounting holes. Once everything is aligned, fully tighten the bolts using a 5mm Allen wrench.
Step 6 - Wire the Backlight Feature
Reconnect the factory headlight harness and locate the OEM accessory power. Unplug the accessory power connector and add the Stage Series backlight harness in-line.
Route the harness along the factory wiring and plug it in-line with each headlight.
Step 7 - Fuse Installation & Final Wiring
Inside the vehicle, pull down on the fuse box cover between the two seats. Depress the side clips and lift the lid off.
Remove the red 10-amp light fuse and replace it with the provided 15-amp fuse.
Step 8 - Test & Final Assembly
Turn on the lights to test functionality. Ensure that low beams, high beams, and backlights are working correctly.
Secure all wiring using zip ties and reassemble the bumper, grille, and interior components in reverse order.
The installation is now complete. Enjoy your new SS3 LED Headlight Kit!
Questions About the Installation?
If you have any questions about installing the SS3 LED Headlight Kit for the 2022-2024 Honda Talon, contact us via our support page.
Where Can I Buy the SS3 LED Headlight Kit for the 2022-2024 Honda Talon?
Visit DiodeDynamics.com or use our Dealer Locator to find a dealer near you.
Looking for more lighting options? Check out our full selection of Honda Talon Lighting Upgrades.
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
This Installation Guide is for the following SKUs: DD7896, DD7897
Share This Post