The SS3 Horizontal LED Fog Light Kit provides a substantial upgrade to your factory fog lights. The SS3 LED Pod Lights included in the kit feature higher output intensity than any other 3” light on the market! SS3 LED Pods Lights have been designed for maximum functionality, with custom-engineered TIR optics shining in highly useful beam patterns, all in a durable package.
With the included angled bezel, the SS3 Horizontal LED Fog Light Kit has a clean, factory-style appearance, only much brighter! The kit is available in a 6000K White that matches most factory LEDs, or a 3000K Yellow to provide high contrast in poor weather conditions. The SS3 LED Pods in the kit also have an available amber backlight that adds a stylish accent light to your vehicle.
Thanks to custom-molded brackets, this LED fog light kit can be installed in minutes. The following installation guide will provide you with basic installation instructions on how to install the SS3 Horizontal LED Fog Light Kit on your vehicle. Check out our installation video, or continue reading for step-by-step instructions below!
Table of Contents
Installation Video
Installation Tools
- Ratchet
- 8mm Socket
- 10mm Socket
- 5/32 Allen Key
- Phillips-Head Screwdriver
- Trim Removal Tool
Ram Plastic Bumper Installation Instructions
Step 1 - Attach LED Pod to Bracket
Install the supplied nuts into the pod housing with the nylon facing inward.
Attach the bracket to the pod using the supplied screws and washers. Make sure the bracket is in the correct orientation.
Ensure that the screws are tightened such that the pod retains its position, but can pivot with force for aiming.
Step 2 - Remove Grille
Using a trim removal tool, remove the four (4) plastic push rivets along the top cover panel.
Using a 10mm socket, remove the four (4) bolts along the top of the grill.
Using a trim removal tool, lift the two (2) tabs located in the lower corners of the grill. Then pull the grill straight out.
Step 3 - Remove Bumper and Factory Fog Lamps
Using an 8mm socket, remove the two (2) bolts on the inner fender liner. Then use a Phillips-Head screwdriver and trim removal tool to remove the two (2) plastic fasteners.
Gently pull the inner fender liner away from the bumper. Then use a 10mm socket to remove the bumper mounting screw from the inner fender.
Using a 10mm socket, remove the four (4) bolts along the bottom of the bumper.
Gently pull the bumper at both corners to release the clips located under the headlights. Then release the five (5) tabs along the top of the bumper and pull straight out.
Remove the factory fog lamp by unplugging the harness. Then depress the tabs on the three (3) push clips and pull the lamp straight out the front.
Step 4 - Install LED Pod
Install your new SS3 pod by pushing it directly into place. Be sure all three (3) push clips seat fully, and are aligned correctly.
Plug the SS3 into the factory fog light harness using the included DT wire adapter. Test for functionality.
Tip: If the light does not turn on, try flipping the connector 180°.
If you purchased backlit SS3 pods, connect the backlight power wire to a fused 12V source to trigger the backlight feature (i.e. parking light or sidemarker); T-Taps are included for this purpose.
Note: Check local laws and regulations for on-road use of the backlight feature. The power source must be fused. Do not connect directly to the vehicle battery.
Repeat Step 4 on the other side and then skip to our aiming instructions before reassembling the truck. To reinstall, reverse the steps we used to take everything apart.
RAM Steel Bumper Installation Instructions
Step 1 - Attach LED Pod to Bracket
Install the supplied nuts into the pod housing with the nylon facing inward.
Attach the bracket to the pod using the supplied screws and washers. Make sure the bracket is in the correct orientation. See the diagrams above.
Ensure that the screws are tightened such that the pod retains its position, but can pivot with force for aiming.
Step 2 - Access Factory Fogs
Using a 10mm socket, remove the bolt on the inner fender liner.
Gently pull the inner fender liner away from the bumper to access your factory fog lights.
Step 3 - Remove Factory Fog Lights
Unplug the factory fog light harness and remove the three (3) 10mm bolts holding the bracket onto the back of the bumper.
Using a pair of needle nose pliers, gently pinch and disconnect the clip holding the factory fog light harness onto the bracket. This clip will be reused.
Remove the factory fog light assembly from the bumper.
Using a pair of needle nose pliers, remove the plastic push clips holding the factory fog light onto the metal bracket.
Step 4 - Install LED Pod
Attach your new SS3 pod to the factory metal bracket. Be sure all three (3) push clips seat fully, and are aligned correctly.
Reinstall the assembled SS3 pod and metal bracket onto the bumper using the three (3) 10mm factory bolts.
Reattach the clip holding the factory fog light harness onto the metal bracket. Then plug the SS3 into the factory fog light harness using the included DT wire adapter. Test for functionality.
Tip: If the light does not turn on, try flipping the connector 180°.
If you purchased backlit SS3 pods, connect the backlight power wire to a fused 12V source to trigger the backlight feature (i.e. parking light or sidemarker); T-Taps are included for this purpose.
Note: Check local laws and regulations for on-road use of backlight feature. Power source must be fused. Do not connect directly to vehicle battery.
Repeat the steps on the other side of the vehicle.
Skip ahead to the aiming instructions before reinstalling the fender liner.
Aiming Instructions
Step 1 - Position Vehicle
Park your vehicle 25 feet away from a wall or garage door on a level surface.
Step 2 - Loosen Allen Bolts
Loosen the 5/32” Allen bolts on each side of your SS3 LED pod just enough to allow you to adjust it.
Step 3 - Measure Mounting Height
On your vehicle, measure the distance between the ground and the center of your SS3 LED Pod. This is your mounting height.
Step 4 - Mark Mounting Height on Wall
Mark the mounting height on the wall or garage door using tape.
Step 5 - Mark Fog Cutoff Line
Add another piece of tape four inches below the mounting height. This is your fog light cutoff line.
Step 6 - Aim SS3 LED Pods
Aim your SS3 LED Pods on each side, so that the top of the beam pattern is on the cutoff line mark.
Step 7 - Tighten Allen Bolts
Tighten the 5/32” Allen bolts back down. Do not overtighten or use power tools to torque them down.
Step 8 - Secure Fender Liner (Optional)
If you removed the fender liner, secure it to the bumper using the original hardware to complete the installation.
Questions About the Installation?
If you have any questions or issues installing the SS3 Horizontal LED Fog Light Kit, please contact us for further assistance.
Where Can I Buy an SS3 Horizontal LED Fog Light Kit?
If you’re ready to upgrade your vehicle with an SS3 Horizontal LED Fog Light Kit, you can purchase one by clicking here or by using our dealer locator to find a dealer near you.
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
This Installation Guide is for the following SKUs: DD6679, DD6680, DD6682, DD6683, DD6714, DD6715, DD7076, DD7077, DD7079, DD7080, DD7081, DD7082
Share This Post